Skip to main content

NOC 94201 · TEER 4

Electronics assemblers, fabricators, inspectors and testers

Wages for Canada

Loading towns...

Job Bank wage

Canada · hourly
Low
$17.50
Median
$22.75
High
$32.00

ESDC Job Bank · 2026 file, revised Nov 18, 2026

Wage trend

Canada · hourly · 2023–2026
2023 $15.50 · $20.00 · $32.00
$20.00
2024 $16.85 · $20.77 · $30.00
$20.77
2025 $17.00 · $20.95 · $29.47
$20.95
2026 $17.50 · $22.75 · $32.00
$22.75

Median +$2.75 since 2023 · top of band +$0.00 · spread narrowed from $16.50 to $14.50

Programs that list this occupation

20 programs

A listing is not a full assessment. Programs that cannot be answered from the occupation alone are left out.

Federal

  • Atlantic Immigration Program: High-Skilled and Intermediate-Skilled Worker
  • Atlantic Immigration Program: International Graduate

Alberta

  • Opportunity Stream

Manitoba

  • Skilled Worker in Manitoba
    No occupation restriction
  • Skilled Worker Overseas
    No occupation restriction

New Brunswick

  • Skilled Worker: New Brunswick Experience
    No occupation restriction
  • Skilled Worker: New Brunswick Graduates
    No occupation restriction
  • Strategic Initiative: Francophone Workers in New Brunswick
    No occupation restriction
  • Strategic Initiative: Francophones Working Remotely
    No occupation restriction
  • Strategic Initiative: New Brunswick Francophone Priorities
    No occupation restriction
Show 10 more programs

Newfoundland and Labrador

  • Skilled Worker Category

Northwest Territories

  • Entry Level and Semi-Skilled Occupations
  • Francophone Stream

Nova Scotia

  • Skilled Worker

Ontario

  • Job Offer for a TEER Category 4 or 5 Employment Position

Prince Edward Island

  • Critical Worker
  • Intermediate Experience
  • International Graduate
    No occupation restriction

Québec

  • Exceptional Talent
    No occupation restriction

Saskatchewan

  • Students

Get your free ImmiReport

Your résumé checked against 65+ immigration programs, with live Job Bank data for your job.

Continue in Lexpoint

Main duties

This group performs some or all of the following duties:

Electronics assemblers and fabricators

  • Solder and manually assemble various electronic components such as resistors, diodes, transistors, capacitors, integrated circuits, switches, wires and other electronic parts to designated locations on printed circuit boards
  • Assemble microcircuits requiring fine hand assembly, the use of microscopes and adherence to cleanroom procedures
  • Install, mount, fasten, align and adjust parts, components, wiring and harnesses to subassemblies and assemblies using hand and small power tools
  • Operate automatic and semi-automatic machines to position, solder and clean prescribed components on printed circuit boards
  • Operate and monitor process equipment including automatic and semi-automatic machines to fabricate electronic components, solder, clean, seal and stamp components and perform other process operations as specified
  • Set up process equipment and adhere to cleanroom procedures as required
  • May replace defective components and repair and overhaul older devices.

Electronics inspectors and testers

  • Inspect electronic components and assemblies to ensure correct component selection and placement, wiring and soldering quality, proper pin insertions, location and diameter of plated holes, breaks in circuitry and line spacing in printed circuit board and other specified requirements while products are being assembled or fabricated
  • Check final assembly for finish, labelling and packaging methods
  • Check mechanical dimensions and perform "go-no-go" electrical tests
  • Identify and mark acceptable and defective assemblies and return faulty assemblies to production for repair

Collect, record and summarize inspection results

  • Investigate equipment malfunction and instruct on proper operation
  • Operate various test equipment and tools to perform simple electrical and continuity testing of electronic components, parts and systems
  • Set up and operate automatic testing equipment to locate circuit and wiring faults, shorts and component defects
  • Compare test results to specifications and set parts or products aside for repair or replace components or parts as indicated by test equipment

Maintain test result reports

  • May conduct life tests (burn-ins) on components, subassemblies and assemblies.

Employment requirements

  • Completion of secondary school is usually required for electronics assemblers, fabricators, inspectors and testers.
  • On-the-job training is usually provided for occupations in this unit group.
  • A two-year apprenticeship program and trade certification for electronics assemblers are available but voluntary in Saskatchewan.
  • Electronics testers may require post-secondary courses in basic electronic theory, testing techniques and testing equipment.
  • Electronics inspectors and testers may require experience as an electronics assembler or component fabricator.

Progression from electronics assembler or component fabricator to electronics inspector or tester is possible with additional training and experience.

Exclusions 4